Precise of 200 125 ccna pdf free practice questions materials and practice exam for Cisco certification for IT engineers, Real Success Guaranteed with Updated ccna 200 125 syllabus pdf dumps vce Materials. 100% PASS CCNA Cisco Certified Network Associate CCNA (v3.0) exam Today!
Q81. - (Topic 5)
Which two tasks does the Dynamic Host Configuration Protocol perform? (Choose two.)
A. Set the IP gateway to be used by the network.
B. Perform host discovery used DHCPDISCOVER message.
C. Configure IP address parameters from DHCP server to a host.
D. Provide an easy management of layer 3 devices.
E. Monitor IP performance using the DHCP server.
F. Assign and renew IP address from the default pool.
The Dynamic Host Configuration Protocol (DHCP) is a network protocol used to configure devices that are connected to a network (known as hosts) so they can communicate on that network using the Internet Protocol (IP). It involves clients and a server operating in a client-server model. DHCP servers assigns IP addresses from a pool of addresses and also assigns other parameters such as DNS and default gateways to hosts.
Q82. - (Topic 8)
Which MAC protocol sets a random timer to reattempt communication?
A. IEEE 802.1x
Q83. - (Topic 8)
Which command can you enter to determine whether a switch is operating in trunking mode?
A. show ip interface brief
B. show vlan
C. show interfaces
D. show interface switchport
Q84. - (Topic 8)
Which MTU size can cause a baby giant error?
Q85. - (Topic 3)
Refer to the exhibit.
C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?
A. These commands need to be added to the configuration: C-router(config)# router eigrp 123
C-router(config-router)# network 172.19.0.0
B. These commands need to be added to the configuration: C-router(config)# router ospf 1
C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
C. These commands need to be added to the configuration: C-router(config)# router rip
C-router(config-router)# network 172.19.0.0
D. No further routing configuration is required.
Since all the same router (C-router) is the default gateway for all three VLANs, all traffic destined to a different VLA will be sent to the C-router. The C-router will have knowledge of all three networks since they will appear as directly connected in the routing table. Since the C-router already knows how to get to all three networks, no routing protocols need to be configured.
Q86. - (Topic 5)
Which statement is correct regarding the operation of DHCP?
A. A DHCP client uses a ping to detect address conflicts.
B. A DHCP server uses a gratuitous ARP to detect DHCP clients.
C. A DHCP client uses a gratuitous ARP to detect a DHCP server.
D. If an address conflict is detected, the address is removed from the pool and an administrator must resolve the conflict.
E. If an address conflict is detected, the address is removed from the pool for an amount of time configurable by the administrator.
F. If an address conflict is detected, the address is removed from the pool and will not be reused until the server is rebooted.
An address conflict occurs when two hosts use the same IP address. During address assignment, DHCP checks for conflicts using ping and gratuitous ARP. If a conflict is detected, the address is removed from the pool. The address will not be assigned until the administrator resolves the conflict.
Q87. - (Topic 7)
Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.
An OSPF neighbor adjacency is not formed between R3 in the main office and R6 in the Branch3 office. What is causing the problem?
A. There is an area ID mismatch.
B. There is a PPP authentication issue; the username is not configured on R3 and R6.
C. There is an OSPF hello and dead interval mismatch.
D. The R3 router ID is configured on R6.
Using the show running-config command we see that R6 has been incorrectly configured with the same router ID as R3 under the router OSPF process.
Q88. - (Topic 5)
In a GLBP network, who is responsible for the ARP request?
C. Active Router
D. Standby Router
Members of a GLBP group elect one gateway to be the active virtual gateway (AVG) for that group. Other group members provide backup for the AVG in the event that the AVG becomes unavailable. The AVG assigns a virtual MAC address to each member of the GLBP group. Each gateway assumes responsibility for forwarding packets sent to the virtual MAC address assigned to it by the AVG. These gateways are known as active virtual forwarders (AVFs) for their virtual MAC address.
The AVG is responsible for answering Address Resolution Protocol (ARP) requests for the virtual IP address. Load sharing is achieved by the AVG replying to the ARP requests with different virtual MAC addresses.
Q89. - (Topic 8)
You are a junior network engineer for a financial company, and the main office network is experiencing network issues. Troubleshoot the network issues.
Router R1 connects the main office to the internet, and routers R2 and R3 are internal routers.
NAT is enabled on router R1.
The routing protocol that is enabled between routers R1, R2 and R3 is RIPv2.
R1 sends the default route into RIPv2 for the internal routers to forward internet traffic to R1.
You have console access on R1, R2 and R3 devices. Use only show commands to troubleshoot the issues.
Users complain that they are unable to reach internet sites. You are troubleshooting internet connectivity problem at main office. Which statement correctly identifies the problem on Router R1?
A. Interesting traffic for NAT ACL is incorrectly configured.
B. NAT configurations on the interfaces are incorrectly configured
C. NAT translation statement incorrectly configured.
D. Only static NAT translation configured for the server, missing Dynamic NAT or Dynamic NAT overloading for internal networks.
Q90. - (Topic 3)
What is the effect of using the service password-encryption command?
A. Only the enable password will be encrypted.
B. Only the enable secret password will be encrypted.
C. Only passwords configured after the command has been entered will be encrypted.
D. It will encrypt the secret password and remove the enable secret password from the configuration.
E. It will encrypt all current and future passwords.
Enable vty, console, AUX passwords are configured on the Cisco device. Use the show run command to show most passwords in clear text. If the service password-encryption is used, all the passwords are encrypted. As a result, the security of device access is improved.
To know more about the 200-125, click here.