200-125 Guide

200-125 Exam Royal Pack (In Stock.)

  • Cisco
  • Exam Number/Code 200-125
  • Product Name CCNA Cisco Certified Network Associate CCNA (v3.0)
  • Questions and Answers
  • 788 Q&As
  • Last Updated
  • Oct 14,2019
  • List Price
  • $128.99
  • Price
  • Today 49.99 USD

Free TrialVersion: demo Buy Now 50% OFF

Top High value 200-125 ebook Tips!

It is impossible to pass Cisco 200-125 exam without any help in the short term. Come to Exambible soon and find the most advanced, correct and guaranteed Cisco 200-125 practice questions. You will get a surprising result by our Avant-garde CCNA Cisco Certified Network Associate CCNA (v3.0) practice guides.

2016 Oct 200-125 practice exam

Q121. - (Topic 5) 

How does a DHCP server dynamically assign IP addresses to hosts? 

A. Addresses are permanently assigned so that the host uses the same address at all times. 

B. Addresses are assigned for a fixed period of time. At the end of the period, a new request for an address must be made, and another address is then assigned. 

C. Addresses are leased to hosts. A host will usually keep the same address by periodically contacting the DHCP server to renew the lease. 

D. Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement. 

Answer: C 

Q122. - (Topic 5) 

Which three features are added in SNMPv3 over SNMPv2? 

A. Message Integrity 

B. Compression 

C. Authentication 

D. Encryption 

E. Error Detection 

Answer: A,C,D 

Q123. - (Topic 4) 

Refer to the exhibit. 

For what two reasons has the router loaded its IOS image from the location that is shown? (Choose two.) 

A. Router1 has specific boot system commands that instruct it to load IOS from a TFTP server. 

B. Router1 is acting as a TFTP server for other routers. 

C. Router1 cannot locate a valid IOS image in flash memory. 

D. Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server. 

E. Cisco routers will first attempt to load an image from TFTP for management purposes. 

Answer: A,C 

Q124. - (Topic 8) 

Refer to the exhibit. 

In the Frame Relay network, which IP addresses would be assigned to the interfaces with point-to-point PVCs? 

A. DLCI 16: /24 

DLCI 17: /24 

DLCI 99: /24 

DLCI 28: /24 

B. DLCI 16: /24 

DLCI 17: /24 

DLCI 99: /24 

DLCI 28: /24 

C. DLCI 16: /24 

DLCI 17: /24 

DLCI 99: /24 

DLCI 28: /24 

D. DLCI 16: /24 

DLCI 17: /24 

DLCI 99: /24 

DLCI 28: /24 

Answer: C 

Q125. DRAG DROP - (Topic 4) 


200-125 free exam questions

Leading 200-125 exam cost:

Q126. - (Topic 4) 

On a corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs? 

A. a router with subinterfaces configured on the physical interface that is connected to the switch 

B. a router with an IP address on the physical interface connected to the switch 

C. a switch with an access link that is configured between the switches 

D. a switch with a trunk link that is configured between the switches 

Answer: A 

Q127. CORRECT TEXT - (Topic 7) 

A network associate is configuring a router for the weaver company to provide internet access. The ISP has provided the company six public IP addresses of The company has 14 hosts that need to access the internet simultaneously. The hosts in the company LAN have been assigned private space addresses in the range of – 

Answer: The company has 14 hosts that need to access the internet simultaneously but we just have 6 public IP addresses from to 

Therefore we have to use NAT overload (or PAT) 

Double click on the Weaver router to open it 

Router>enable Router#configure terminal 

First you should change the router's name to Weaver 

Router(config)#hostname Weaver 

Create a NAT pool of global addresses to be allocated with their netmask. 

Weaver(config)#ip nat pool mypool netmask 

Create a standard access control list that permits the addresses that are to be translated 

Weaver(config)#access-list 1 permit 

Establish dynamic source translation, specifying the access list that was defined in the prior step 

Weaver(config)#ip nat inside source list 1 pool mypool overload 

This command translates all source addresses that pass access list 1, which means a source address from to, into an address from the pool named mypool (the pool contains addresses from to 

Overload keyword allows to map multiple IP addresses to a single registered IP address (many-to-one) by using different ports 

The question said that appropriate interfaces have been configured for NAT inside and NAT outside statements. 

This is how to configure the NAT inside and NAT outside, just for your understanding: 

Weaver(config)#interface fa0/0 

Weaver(config-if)#ip nat inside 


Weaver(config)#interface s0/0 

Weaver(config-if)#ip nat outside 


Finally, we should save all your work with the following command: 

Weaver#copy running-config startup-config 

Check your configuration by going to "Host for testing" and type: 

C :\\>ping 

The ping should work well and you will be replied from 

Q128. - (Topic 6) 

Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch? (Choose two.) 

A. SW1#show port-secure interface FastEthernet 0/12 

B. SW1#show switchport port-secure interface FastEthernet 0/12 

C. SW1#show running-config 

D. SW1#show port-security interface FastEthernet 0/12 

E. SW1#show switchport port-security interface FastEthernet 0/12 

Answer: C,D 

Q129. - (Topic 3) 

What is the alternative notation for the IPv6 address B514:82C3:0000:0000:0029:EC7A:0000:EC72? 

A. B514 : 82C3 : 0029 : EC7A : EC72 

B. B514 : 82C3 :: 0029 : EC7A : EC72 

C. B514 : 82C3 : 0029 :: EC7A : 0000 : EC72 

D. B514 : 82C3 :: 0029 : EC7A : 0 : EC72 

Answer: D 

Q130. CORRECT TEXT - (Topic 6) 

A network associate is adding security to the configuration of the Corp1 router. The user on host C should be able to use a web browser to access financial information from the Finance Web Server. No other hosts from the LAN nor the Core should be able to use a web browser to access this server. Since there are multiple resources for the corporation at this location including other resources on the Finance Web Server, all other traffic should be allowed. 

The task is to create and apply an access-list with no more than three statements that will allow ONLY host C web access to the Finance Web Server. No other hosts will have web access to the Finance Web Server. All other traffic is permitted. 

Access to the router CLI can be gained by clicking on the appropriate host. 

All passwords have been temporarily set to "cisco". The Core connection uses an IP address of The computers in the Hosts LAN have been assigned addresses of - 

Host A 

Host B 

Host C 

Host D 

The servers in the Server LAN have been assigned addresses of - 

The Finance Web Server is assigned an IP address of 

Answer: Select the console on Corp1 router 

Configuring ACL 


Corp1#configure terminal 

comment: To permit only Host C ({source addr} to access finance server address ( {destination addr} on port number 80 (web) 

Corp1(config)#access-list 100 permit tcp host host eq 80 

comment: To deny any source to access finance server address ( {destination addr} on port number 80 (web) 

Corp1(config)#access-list 100 deny tcp any host eq 80 

comment: To permit ip protocol from any source to access any destination because of the implicit deny any any statement at the end of ACL. 

Corp1(config)#access-list 100 permit ip any any 

Applying the ACL on the Interface 

comment: Check show ip interface brief command to identify the interface type and number by checking the IP address configured. 

Corp1(config)#interface fa 0/1 

If the ip address configured already is incorrect as well as the subnet mask. this should be corrected in order ACL to work 

type this commands at interface mode : 

no ip address 192.x.x.x 255.x.x.x (removes incorrect configured ipaddress and subnet mask) 

Configure Correct IP Address and subnet mask : 

ip address ( range of address specified going to server is given as - ) 

Comment: Place the ACL to check for packets going outside the interface towards the finance web server. 

Corp1(config-if)#ip access-group 100 out 


Important: To save your running config to startup before exit. 

Corp1#copy running-config startup-config 

Verifying the Configuration: 

Step1: show ip interface brief command identifies the interface on which to apply access list. 

Step2: Click on each host A, B, C, & D. Host opens a web browser page, Select address box of the web browser and type the ip address of finance web server ( to test whether it permits /deny access to the finance web Server. 

Step 3: Only Host C ( has access to the server. If the other host can also access then maybe something went wrong in your configuration. Check whether you configured correctly and in order. 

Step 4: If only Host C ( can access the Finance Web Server you can click on NEXT button to successfully submit the ACL SIM. 

To know more about the 200-125, click here.

Tagged as : Cisco 200-125 Dumps, Download 200-125 pdf, 200-125 VCE, 200-125 pass4sure, examcollection 200-125